Brett Williams - Whisper X Project

Share details of your Whisper project with the community.

Re: Brett Williams - Whisper X Project

Postby Brett » Thu May 21, 2015 10:09 pm

No I have not covered it yet as I need to shape the horn. I may do that tomorrow, but will only start the glass work next week.
Brett
 
Posts: 39
Joined: Fri Nov 02, 2012 9:10 pm

Re: Brett Williams - Whisper X Project

Postby Pieter001 » Fri May 22, 2015 4:44 pm

I also need to shape that counter balance horn, worried about not getting it right... Will see what I can conjure up to make it as symmetric as possible as I do not trust my judgement that much :lol:

Good luck, have fun and do post a pick ;)
Pieter001
 
Posts: 157
Joined: Wed Jul 03, 2013 7:03 pm
Location: Heidelberg GP

Re: Brett Williams - Whisper X Project

Postby Pieter001 » Fri Jul 17, 2015 7:36 am

Hi Brett,

Have you had a chance to weight your rudder? I'm going to NZ for a while, but I'm going to try my utmost at completing my rudder before I leave. It will be great to close the rudder chapter before I go :D

Regards,

Pieter
Pieter001
 
Posts: 157
Joined: Wed Jul 03, 2013 7:03 pm
Location: Heidelberg GP

Re: Brett Williams - Whisper X Project

Postby Brett » Sat Jul 18, 2015 6:44 pm

Pieter I keep on forgetting to weigh it!!. I am away for 4 days this week and will try to remember when I am back.
Brett
 
Posts: 39
Joined: Fri Nov 02, 2012 9:10 pm

Re: Brett Williams - Whisper X Project

Postby Brett » Sat Jul 18, 2015 6:47 pm

We cut the elevator today. Took a lot of decision making where to make the cut. Thankfully Russell was close by to give advice. I did not want to start fiddling with the mass balance so it was a juggle in the end.
IMG_0080.JPG
IMG_0080.JPG (295 KiB) Viewed 7948 times
Brett
 
Posts: 39
Joined: Fri Nov 02, 2012 9:10 pm

Re: Brett Williams - Whisper X Project

Postby Pieter001 » Sun Jul 19, 2015 11:28 am

Well done Brett, I can relate to the tension before such a big CUT :)
Pieter001
 
Posts: 157
Joined: Wed Jul 03, 2013 7:03 pm
Location: Heidelberg GP

Re: Brett Williams - Whisper X Project

Postby MNortier » Sun Aug 16, 2015 4:08 pm

Hi Brett,

You are doing an outstanding job....cant wait to be your wingman over USA! April is just 9 months away! Hurry up! :lol:

Rgds

Morné
MNortier
 
Posts: 109
Joined: Sat May 09, 2015 6:02 pm
Location: FAOH

Re: Brett Williams - Whisper X Project

Postby Brett » Mon Aug 24, 2015 8:22 pm

Hey Morne - get the container prices for Oshkosh :D :D
Brett
 
Posts: 39
Joined: Fri Nov 02, 2012 9:10 pm

Re: Brett Williams - Whisper X Project

Postby Brett » Mon Aug 24, 2015 8:34 pm

I have decided to insert the wing tie down points like Russell has done. I bought an M8 longnut, eye bolt and a counter sink bolt as in the picture. I then mounted it very carefully to the spar in line with the point where the aileron ends. I removed some foam under the spar cap as well so as to make the internal space bigger than the hole that the nut gets inserted into. We then wrapped roving on the nut and bolt and stuffed cotton flox into hole - full. Inserted the bolt and nut and we now have a very strong tie down point and a lekker handvatsel to carry the wing upright.

IMG_0091.JPG
IMG_0091.JPG (487.36 KiB) Viewed 7839 times


IMG_0092.JPG
IMG_0092.JPG (617.23 KiB) Viewed 7839 times
Brett
 
Posts: 39
Joined: Fri Nov 02, 2012 9:10 pm

Re: Brett Williams - Whisper X Project

Postby Brett » Sat Sep 05, 2015 8:14 pm

Some progress being made.

IMG_0095.jpg
IMG_0095.jpg (25.54 KiB) Viewed 7764 times


IMG_0094.jpg
IMG_0094.jpg (25.74 KiB) Viewed 7764 times
Brett
 
Posts: 39
Joined: Fri Nov 02, 2012 9:10 pm

PreviousNext

Return to My Whisper Project

Who is online

Users browsing this forum: No registered users and 1 guest

cron